1. Install correctly
(1) El cattle poultry feed grinding and mixing machine must be fixedly installed, and the axis of the crusher pulley and the power machine pulley should be parallel, and the grooves of the two drive pulleys must be in the same straight line. Otherwise, not only will the damage of the parts be accelerated, but the belt will be easily dropped.
(2) Si es necesario modificar la polea, debe calcularse para satisfacer las necesidades de la velocidad del husillo del feed crushing and mixing equipment. Do not increase the spindle speed at will. When the speed exceeds 15% of the rated speed, the equipo de trituración y mezcla de piensos para aves de corral will vibrate violently.
(3) The raw materials should be carefully cleaned up in advance, sieved or selected if necessary, to prevent iron and stones from entering the feed grinding mixing machine.
(4) Before each use, open the cover of the animal feed hammer mill crushing equipment to check whether there is any damage to all parts of the animal feed hammer mill grinding machine, especially whether the split pin on the rotor is intact and whether the connection is loose. After confirming that it is intact, close the cover firmly and screw in the handwheel on the door. Drag the belt by hand to check whether the moving part is flexible, whether there are abnormal noises and jams.
(5) Después de la grain corn grinder crusher for animal feed se pone en marcha, es necesario que funcione al ralentí durante 2-3 minutos, y luego añadir gradualmente los materiales después de la operación normal.
(6) The operator should tighten the cuffs, wear a mask, and work with gloves is strictly prohibited; stand on the side of the corn grinder for animal feed when feeding materials to prevent rebound debris from hurting the face; when crushing long-stalk crops, do not pinch their hands Tighten to prevent the hand from being hurt by the crop.
(7) Feeding should follow the principle of "uniform feeding, small amount and quick feeding", that is, from less to more, until the load is normal, and maintain continuous and uniform to prevent clogging.
(8) If the material inlet is blocked, do not poke with wooden sticks or iron rods to prevent the sticks from being brought into the machine or ejected and hurt people. It is also not allowed to reach into the material inlet to shift the material. Harder The stems push the raw materials into the crushing chamber.
(9) Pay close attention to the operation. If you find vibration, abnormal noise, blockage or spraying materials, you should stop the machine immediately and check and eliminate it. It is strictly forbidden to use wooden sticks or hands to forcibly feed or pull out materials without stopping to avoid impact Injure your arm or break the machine.
(10) Está terminantemente prohibido abrir la puerta cuando el animal feed grinding mill crusher is running; the belt drive should be equipped with protective devices; long-term overload operation is forbidden; various tools are not allowed to be placed on the crusher and materials at will, so as not to fall into the machine; Smoking is prohibited in the place, and pay attention to waterproof and moisture-proof.
(11) La bolsa de polvo de fabricación propia debe ser de tela con buena permeabilidad al aire, y su longitud no debe ser inferior a 1,5 m. Si la bolsa de polvo no está ventilada o es demasiado corta, puede provocar una pulverización de retorno en la entrada.
(12) Feeding should be stopped before shutting down, and the machine should be shut down after the materials in the standby are drained. After the operation, dust and lubrication should be timely.
2. Adjustment points
(1) Hay una compuerta o deflector en la parte inferior de la tolva, y la cantidad de alimentación se puede controlar ajustando la apertura de la compuerta o deflector. Por ejemplo, cuando se procesan tortas de frijol, las tortas de frijol deben ser trituradas primero, y el tamaño máximo después de la trituración no debe exceder 40mtn; cuando se procesan vides de camote, las vides deben ser picadas primero, y la longitud no debe exceder 150mm. Al controlar la cantidad de alimentación, se puede mejorar la eficiencia del trabajo y la calidad de trituración, y se puede evitar la sobrecarga.
(2) En general, feed mill factory use hammer mill grinders have 2-3 kinds of screens with different apertures (such as claw grinders with apertures of Φ0.6nm, Φ1.2mm, and Φ3.5mm), change different apertures when using The screen mesh can get different crushing particle size.
When installing the screen, you should correctly choose the overlap method at the screen joint according to the rotation direction of the rotor, so that the inner interface direction is the same as the rotation direction to avoid material blocking; if the screen hole is tapered, because The small hole end usually has a small amount of burrs. To facilitate discharging, the large hole end should be installed outward.
(3) El tamaño de la puerta de aire también se puede ajustar para controlar el tamaño de la puerta de aire cuando se instala la bomba de aire.
3.Introduction of RICHI Ce approval animal poultry cattle chicken fish pig feed grinding hammer mill machine
（1）Features
•Used for the grinding of raw materials like organic garbage, drug residue, winery, sugar, etc.
•Used for the grinding of biological fermentation wet materials, like livestock and poultry excrement.
•The water allowable value of organic fertilizer materials reaches 25-55%, and particle size can reach the requirement of pelleting.
•Solve the problem of materials with high moisture, the grinding of organic materials treated by fermentation has better effect.
•High-speed rotating blade makes good grinding fineness, high efficiency and low energy consumption.
•Use high alloy wear-resistant hammer, more wear-resistant than ordinary hammer, and the service life of the hammer is increased.
（2）Models
-SFSP66*80b electric cattle feed corn hammer mill(10-13t/h)
-SFSP66*80a hot sale high quality grain corn hammer mill(8-10t/h)
