1. Check rectificadora de piensos before debugging

(1) For newly installed equipment, when the equipment is in place and the crushing chamber is connected, it is inevitable that foreign objects such as iron blocks, welding rod heads, welding slag and so on will remain. Without turning on the fan and main motor, open the impurity removal baffle below the feed inlet to allow impurities and washing materials to be discharged from here. After the end, open the observation door of the ultrafine pulverizer to check whether there are impurities in the pulverizing disc, and whether there is any hidden danger of collision between the hammer knife and the gear ring.

(2) After the initial check that everything is normal, power on the equipment. Check the direction of rotation of all motors.

(3) Check and set the parameters of the two inverters of the feeding motor and the grading wheel motor of the ultra-fine pulverizer, and check whether the adjustment of the air switch, contactor, thermal relay, and overcurrent relay corresponding to the motor is appropriate? Re-lock all the wires once again.

(4) Check whether the solenoid valve blows normally or not, and adjust the solenoid valve pulse width and spray interval time of the dust collector.

(5) Check whether there is any air leakage in the air shutter under the brake. You can put your hand or fine powder on the interface to see if it feels like sucking in. If necessary, seal it. After the above check everything is normal, prepare to produce with materials.

2. Debugging process

(1) En este momento, tome una muestra en la zona de producto acabado para comprobar la finura del polvo acabado. Cuando la finura supera el índice, la velocidad de la rueda de clasificación puede ajustarse a la baja.

(2) Cada vez que se ajuste la velocidad de rotación de la rueda de clasificación, deberá transcurrir un tiempo para comprobar la finura del polvo acabado.

(3) Siempre que disminuya la velocidad de rotación de la rueda clasificadora, también disminuirá la corriente del motor principal. En este momento, la frecuencia de alimentación se puede aumentar gradualmente para aumentar la producción de trituración.

(4) Al mismo tiempo, ajustar el rango de apertura de la puerta de aire del ventilador de alta presión, y detectar la corriente del ventilador de alta presión, no sólo para garantizar un cierto volumen de aire, sino también para permitir que el ventilador funcione normalmente durante mucho tiempo.

(5) Si el rendimiento y la finura no cumplen los requisitos debido a diferencias de material, el sentido de rotación de la rueda de clasificación también puede ser el mismo que el del motor principal. Otros métodos de depuración son los mismos que los anteriores.

3. Superfine feed grinder equipment adjustment and maintenance

(1) The main wearing parts of the grinder: flat teeth, round teeth, large and small grinding teeth. Flat teeth and round teeth are made of stainless steel, with good dynamic balance, and should be replaced if they are severely worn. The size of the self-made metal processing should be specifications, and the weight difference of each piece should not be more than 1 gram to avoid vibration damage to the bearing and the machine.

(2) 0.6-12 mm sieves of various specifications. When replacing, the light side is down.

(3) Los cojinetes se rellenan regularmente con grasa de alta velocidad y se revisan una vez cada medio mes. Si se detecta un desgaste grave, deben sustituirse o repararse a tiempo.

(4) Collision is strictly prohibited, and the inside and outside of the machine should be cleaned up for a long time, and kept properly to prevent rust.

(5) Si no puede funcionar con normalidad por motivos de fabricación, el usuario puede ponerse en contacto directamente con el fabricante para obtener una garantía gratuita.

4. Precautions for the operation of the superfine grinder for animal feed

(1) The operator should stand on the side of the feeding port, and it is forbidden to reach into the feeding port. Do not open the cover during operation and the machine is not stopped.

(2) Load start is strictly forbidden. When the feeding port is blocked, it is forbidden to forcibly feed it by hand or with a wooden stick. It should be shut down immediately for inspection. When working, it is necessary to feed the material in an appropriate amount and evenly. If there is a semi-wet non-dry material, it is best to dry it or reduce the feeding amount.

5. Maintenance and storage of superfine feed grinding machine for animal poultry livestocks

(1) Always check the fastening of each part to prevent it from loosening and falling off and damaging the machine.

(2) The oil filling holes should be filled frequently, and the bearing parts should be cleaned and filled with lithium grease every six months.

(3) When the machine is shut down for operation, the machine should be idling for a period of time, the remaining material in the machine should be blown off, and then shut down.

(4) When the machine is out of service, the debris outside the machine should be removed, all rotating parts should be filled with grease, and stored in a dry air, no corrosive gas warehouse.

RICHI máquina trituradora de piensos serie

1.animal cattle poultry cow fish feed crusher machine(10-13t/h)

2.CE animal feed crusher machine for grinding feed powder(8-10t/h)

3.Ce approval animal fodder grinder equipment(6-9t/h)

4.grain corn grinder for animal feed(4-6t/h)